← Spill Compliance Resource Center
Rain carries spilled oil, coolant and chemicals straight into storm drains and on to creeks, rivers and the ocean. If your facility has an industrial stormwater permit, it has spill prevention and response requirements, and inspectors look for them.
The short version
- Facilities in the industrial categories listed in 40 CFR 122.26(b)(14) need permit coverage for stormwater. That includes manufacturers, transportation facilities with vehicle maintenance or fueling, recycling yards and landfills.
- A few places get coverage from EPA’s Multi-Sector General Permit (MSGP); most states, including California, issue their own industrial permit.
- Every one of these permits requires a Stormwater Pollution Prevention Plan (SWPPP) with spill prevention and response measures.
- EPA’s permit spells it out: clean up with dry methods such as absorbents, use secondary containment, label containers, train people, and keep spill kits on site near where spills may happen.
Who needs a permit
The Clean Water Act requires an NPDES permit for stormwater “associated with industrial activity.” 40 CFR 122.26(b)(14) lists the categories, from manufacturing plants to transportation facilities that do vehicle maintenance, fueling or equipment cleaning.
Where EPA is the permitting authority (a handful of states and territories, including Massachusetts, New Hampshire and New Mexico, plus Indian country and some federal facilities), coverage comes from EPA’s Multi-Sector General Permit. Everywhere else, your state issues the permit. California’s is the Industrial General Permit (IGP).
What EPA’s permit requires for spills
Part 2.1.2.4 of the 2021 MSGP, “Spill Prevention and Response,” requires you to minimize leaks and spills that could reach stormwater and to plan how you will respond. The listed measures include:
- Clean up spills and leaks promptly using dry methods, such as absorbents.
- Use drip pans and absorbents under leaky vehicles and equipment stored outdoors.
- Use spill and overflow protection equipment.
- Plainly label containers that could spill or leak (for example “Used Oil” or “Spent Solvents”).
- Use secondary containment and barriers between material storage and traffic areas, or a similarly effective method.
- Train staff to stop, contain and clean up leaks and spills quickly.
- Keep spill kits on site, near areas where spills may occur or where a rapid response can be made.
- Notify the right people when a spill happens, and report reportable quantities (see below).
Your SWPPP has to describe these procedures, and EPA’s sector-specific requirements add more for some industries.
California’s Industrial General Permit
California’s IGP (Order 2014-0057-DWQ, as amended) makes spill and leak prevention and response one of its minimum best management practices (Section X.H.1.c). You must:
- Set up procedures or controls to minimize spills and leaks.
- Develop response procedures that keep spilled materials out of the storm drain system, and clean up and dispose of spills promptly and properly.
- Identify the spill response equipment you need, where it is kept, and how it is maintained.
- Identify and train your spill response personnel.
Other states use similar language. Check your own permit for the exact wording.
Protecting your storm drains
- Know where your drains are. Mark storm drains on your site map and on the ground, so anyone can find them in a hurry.
- Cover drains during risky work. Seal nearby drains with a drain cover during fueling, unloading, transfers and outdoor washing.
- Contain outdoor storage. Keep drums and totes on spill pallets or inside berms, and keep them out of traffic lanes.
- Catch drips. Put drip pans or absorbent pads under parked equipment that leaks, and fix the leak.
- Use oil-only absorbents outside. They repel water, so they keep working in the rain and pick up oil without soaking up the puddle.
- Clean up dry. Never hose a spill toward a drain. Absorb it, sweep it up and dispose of it properly.
Reporting a spill
If a spill of oil or a hazardous substance meets a federal reportable quantity (40 CFR parts 110, 117 or 302), call the National Response Center at (800) 424-8802 as soon as you know about it. For oil, a discharge that causes a sheen on water is reportable. State and local agencies often have their own reporting rules, so keep their numbers posted where people can find them.
Products that help
Stormwater spill checklist
- Confirm whether your facility needs industrial stormwater coverage, and from whom.
- Mark every storm drain on your site map and on the ground.
- Keep spill kits near fueling, loading, storage and maintenance areas, and restock after each use.
- Store drums and totes on containment, away from traffic and drains.
- Cover drains during fueling, unloading and outdoor washing.
- Train staff to clean up dry, and post spill reporting numbers.
- Write your spill procedures into your SWPPP and keep them current.
Sources
Not sure what fits your site? Call (800) 869-9633, Mon–Fri 9–5 PT, or email [email protected]. Tell us what you store and where, and we’ll help you size it.
Last reviewed November 2026 against the current Code of Federal Regulations (eCFR). This is a plain-English summary, not legal advice. State rules, local fire codes and your own plan or permit can be stricter, so check the regulation text and your permit before you rely on it.

